Rc 컨트롤러 서보모터 범위제한 방법

자율운항선박
1

서브모터 키 각도 제한이 60~120도 되어있어서 원격으로 rc 조종할때 휠을 최대로 돌릴 시 연결부분이 갈리는 현상이 발생하여서 혹시 rc조종을 최대 각도로 휠을 돌렸을때 좌우 60도와 120도로 맞추는 방법이 어떻게 되는지 궁금합니다

2

5.4 Trim Setting

This function is used to adjust the channel trim.

For 2-in-1 mode, only CH1-CH4 trim can be adjusted. For non-2-in-1 mode, CH1-CH7 trim can be adjusted.

  • When the steering wheel is in the neutral position, press the ST+/- button to adjust CH1 and CH3-CH7 trim. By default, the CH1 trim is adjusted. To adjust CH3-CH7, first switch to the corresponding channel. When CH7 is set to rear wheel steering only, CH7 trim can be adjusted by pressing the ST+/- button in CH1.
  • When the throttle trigger is in the neutral position, press the TH+/- button to adjust the CH2 trim.

ST+/TH+: Press to increase the trim value. ST-/TH-: Press to decrease the trim value. The trim range: -120 us~120 us.
The step is 4us. By default, it is 0.

When the trim setting action takes effect, the buzzer will beep once shortly in Tone 1. You can press and hold it for quick adjustment. The buzzer will beep twice shortly when the trim is over Neutral. The buzzer will sound once for seconds when it reaches the end.

5.5 D/R Setting

This function is used to adjust the travel range value of the channel.

For 2-in-1 mode, only CH1-CH4 travel range value can be adjusted. For non-2-in-1 mode, CH1-CH7 travel range value can be adjusted.

  • When the steering wheel is located in the maximum travel or minimum travel, press the ST+/- button to adjust CH1 and CH3-CH7 travel range value. By default, the CH1 travel range value is adjusted. To adjust CH3-CH7, first switch to the corresponding channel. When CH7 is set to rear wheel steering only, CH7 travel range value can be adjusted by pressing the ST+/- button in CH1.
  • When the throttle trigger is at the maximum or minimum travel, press the TH+/- button to adjust CH2 travel range value.

ST+/THt: Increase the travel value. ST-/TH-: Decrease the travel value. Travel range: 0-120%, by default, it is 100%, the step is 5%.

When the servo setting action takes effect, the buzzer will beep once shortly in Tone 2. You can press and hold it for quick adjustment. The buzzer will sound for seconds when it reaches the end.

5.5 내용처럼 컨트롤러 휠을 시계방향 또는 반시계방향 끝까지 움직인 상태에서 ST 버튼을 누르면 조절할 수 있습니다.
범위를 줄여야 하기 때문에 - 버튼을 누르면 됩니다.
휠을 돌리면 모터가 움직이니 모터를 분리하거나 모터의 기어를 분리한 상태에서 진행해주세요.

참고로 센터가 맞지 않다면 5.4 내용처럼 조절할 수 있습니다.

FS-MG7 User manual 20221121-EN Retail Version.pdf (3.3 MB)

RC 컨트롤러 메뉴얼을 첨부하니 참고해주세요.